Problem analysis for transportation of urea hydrolysis production gas for thermal power plants

ZHANG Bo; ZHANG Xiangyu; LI Minghao; TIAN Wenchao; XU Hongjie; NIU Guoping; CHANG Lei; JIA Linquan

English

您当前的位置：

首页 >

文章列表页 >

Problem analysis for transportation of urea hydrolysis production gas for thermal power plants

Thermal Power Generation Vol. 44, Issue 11, Pages: 114-117(2015)

更新时间：2025-09-28

- Problem analysis for transportation of urea hydrolysis production gas for thermal power plants
- 作者机构：
  
  西安热工研究院有限公司
- 作者简介：
- 基金信息：
- DOI：
  CLC： TM621.8
- Published：2015
- 稿件说明：
移动端阅览
ZHANG Bo, ZHANG Xiangyu, LI Minghao, et al. Problem analysis for transportation of urea hydrolysis production gas for thermal power plants[J]. Thermal Power Generation, 2015, 44(11): 114-117.
DOI：

ZHANG Bo, ZHANG Xiangyu, LI Minghao, et al. Problem analysis for transportation of urea hydrolysis production gas for thermal power plants[J]. Thermal Power Generation, 2015, 44(11): 114-117. DOI：

摘要

针对尿素水解产品气输送过程中存在的蒸汽回凝、氨基甲酸铵结晶析出等问题

分析了给料尿素溶液质量分数和水解反应器运行压力对产品气成分、蒸汽回凝温度和氨基甲酸铵结晶析出温度的影响。结果表明:蒸汽回凝温度和氨基甲酸铵结晶析出温度由给料尿素溶液质量分数和水解反应器运行压力决定;当运行压力0.7 MPa

给料溶液质量分数为50%时

产品气中水蒸气的回凝温度为133℃

氨基甲酸铵的结晶析出温度为85℃。并建议在设计伴热管道保温时

选用硬质或半硬质圆形保温材料

根据允许最大散热损失小于104 W/m2

计算保温层厚度。

Abstract

Steam condensation

ammonium carbamate crystallization and other problems occurred during transportation of urea hydrolysis production.Thus

effects of the urea liquid mass fraction and reactor pressure on such parameters such as the compositions of the production gas

the steam condensation temperature and the ammonium carbamate crystallization temperature were investigated.The results show that

the steam condensation temperature and the ammonium carbamate crystallization temperature depended on the urea liquid mass fraction and reactor pressure.When the operation pressure was 0.7MPa and the feed mass fraction was 50%

the steam condensation temperature of the production gas was 133℃and the crystallization temperature of the ammonium carbamate was 85 ℃.Moreover

it is suggested that during the thermal insulation pipeline design

the hard or semi-hard circular thermal insulation material should be selected

and the insulation layer thickness be calculated according to the allowance maximum heat disspation rate(104 W/m2).

关键词

Keywords

references

Views

213

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Failure analysis of flange used for urea hydrolysis equipment

Research and application of data-based optimization technology for operation of denitrification system in utility boilers

Model for predicting SCR flue gas denitration efficiency based on particle swarm optimization and twin support vector machine

Design of flue gas denitration control system based on feedforward constrained dynamic matrix control

Related Author

HUANG Jinyang

YANG Zheng

LU Jintao

ZHANG Bo

YANG Zhen

XU Hongjie

姜龙

李金晶

Related Institution

Xi'an Thermal Power Research Institute Co.,Ltd.

Focused Photonics (Hangzhou) Inc.

School of Information Science and Technology, Zhejiang Sci-Tech University

Xi’an Thermal Power Research Institute Co., Ltd.

Fujian Electric Power Survey & Design Institute

AI问答

⁰