A real-time monitoring model for heat consumption rate of steam turbine unit based on unit power

ZHAI Zhaoyin; WANG Jizhou; LI Jianlan; CHEN Gang

English

您当前的位置：

首页 >

文章列表页 >

A real-time monitoring model for heat consumption rate of steam turbine unit based on unit power

Thermal Power Generation Vol. 44, Issue 10, Pages: 15-19(2015)

更新时间：2025-09-28

- A real-time monitoring model for heat consumption rate of steam turbine unit based on unit power
- 作者机构：
  
  华中科技大学能源与动力工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC： TM621
- Published：2015
- 稿件说明：
移动端阅览
ZHAI Zhaoyin, WANG Jizhou, LI Jianlan, et al. A real-time monitoring model for heat consumption rate of steam turbine unit based on unit power[J]. Thermal Power Generation, 2015, 44(10): 15-19.
DOI：

ZHAI Zhaoyin, WANG Jizhou, LI Jianlan, et al. A real-time monitoring model for heat consumption rate of steam turbine unit based on unit power[J]. Thermal Power Generation, 2015, 44(10): 15-19. DOI：

摘要

针对火电机组热耗率在线计算不准确的问题

提出了一种基于机组功率的实时热耗率计算方法:由机组热力性能试验数据获得汽轮机各缸性能特性

进而得出各加热器抽汽和进汽参数以及汽轮机低压缸效率;根据热平衡、能量守恒和质量平衡等基本原理

建立了基于发电机功率的热力系统模型;利用反平衡方法计算得到汽轮机各段抽汽流量和主蒸汽流量

从而得出机组实时热耗率。将该方法应用于某660MW机组的实时热耗率计算

并与厂级监控信息系统(SIS)计算的机组热耗率进行对比。结果表明

本模型计算的机组热耗率精度更高、稳定性更好

可为电厂热经济性的准确评价提供数据依据。

Abstract

In the view of the problem that the heat consumption rate calculation is inaccurate in present power plants

a new calculation method for real-time heat consumption rate based on power measurement is developed in this paper.Firstly

through the analysis of design data and thermal performance test results

the operating characteristics of steam turbine were obtained

and the extraction steam and entrance steam parameters of each heater were also obtained as well as the low pressure cylinder efficiency

which completes the loss of field monitoring data.Secondly

the thermal system model of the power plant was established based on the power measurement

according to the principle of thermal equilibrium

material balance and energy conservation.To get the heat consumption rate in real time

the counterbalance method was employed to calculate the extraction steam flow in different tubes and main steam flow rate without measuring the condensate flow.Finally

this method was applied on a 600 MW unit and the monitoring results were compared with that calculated by the SIS.The results show that this power-based model has high accuracy and stability in heat consumption rate calculation

which provides technical support for accurate evaluation of power plant thermal efficiency.

关键词

Keywords

references

Views

232

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Experimental study on thin-layer microwave drying characteristics of Ximeng lignite

LOW LOAD OPERATION AND ECONOMIC ANALYSIS OF 125MW STEAM TURBINE

CAUSE ANALYSIS OF OVER-TEMPRATURE OCCURRED ON THRUST BEARING SHOE OF A N50-8.83-II TYPE TURBINE-GENERATOR SET

ANALYSIS AND STUDY ON THE FAULT DIAGNOSIS METHOD OF VACUUM IN CONDENSOR FOR STEAM TURBINE UNIT

CALCULATION OF LOW PRESSURE CYLINDER EFFICIENCY IN SIMPLIFIED THERMAL PERFORMANCE TEST OF STEAM TURBINE

Related Author

LIU Jianzhong

ZHU Jiefeng

CHEN Ruiqi

HUANG Zhihui

YI Ningtong

陈吉荣

李新民

雷如意

Related Institution

State Key Laboratory of Clean Energy Utilization, Zhejiang University

Hancheng

Hancheng Power Plant Shaanxi Hancheng

Hancheng Power Plant

Shanxi Yongji

AI问答

⁰