Effect of rotor speed on heat transfer of blades:numerical simulation

ZHANG Ling; WANG Chong

English

您当前的位置：

首页 >

文章列表页 >

Effect of rotor speed on heat transfer of blades:numerical simulation

Thermal Power Generation Vol. 44, Issue 7, Pages: 23-27(2015)

更新时间：2025-09-28

- Effect of rotor speed on heat transfer of blades:numerical simulation
- 作者机构：
  
  东北电力大学能源与动力工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC： TK471
- Published：2015
- 稿件说明：
移动端阅览
ZHANG Ling, WANG Chong. Effect of rotor speed on heat transfer of blades:numerical simulation[J]. Thermal Power Generation, 2015, 44(7): 23-27.
DOI：

ZHANG Ling, WANG Chong. Effect of rotor speed on heat transfer of blades:numerical simulation[J]. Thermal Power Generation, 2015, 44(7): 23-27. DOI：

摘要

为了研究尾迹脱落频率对动叶传热及其气膜冷却效率的影响

采用SSTk-ω紊流模型

在Simple算法基础上

利用有限体积法对无气膜孔和前缘有3排气膜孔情况下

转速分别为500

1 000

2 000r/min时动叶表面的努赛尔数(Nu)分布进行数值模拟。结果表明:随着转速的增大

无孔和有孔时的冷却效果差异明显

无孔时随转速增加动叶压力面和吸力面Nu逐渐降低

传热效果较差

有孔时则相反

换热增强

冷却效果较好。

Abstract

To investigate the effect of vertex shedding frequency on heat transfer and gas film cooling of the rotor blade

on the basis of Simple algorithm

the SSTk-ωturbulence model and finite volume method were adopted to discrete the control equations.Under conditions with no film-cooling hole and three rows of film-cooling holes at front edge of the blade

the effect of rotor speed on gas film cooling performance was numerically studied.The rotor speeds of 500r/min

1 000r/min and 2 000r/min were selected as the simulation conditions.The Nusselt number distribution on rotor surface was obtained.The results show that

with the increasing rotor speed

there's dramatic difference in cooling effectness between the blade with no film-cooling hole and the one with three rows of film-cooling holes.For the rotor with no film-cooling hole

the Nusselt number on pressure side and suction side of the rotor reduced gradually with an increase in rotor speed

so the heat transfer performance was relatively poor.While for the rotor with three rows of filmcooling holes

the heat transfer was enhanced and the film cooling efficiency was higher.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Numerical simulation of influence of equivalence ratio on combustion and NOx formation in a DLE combustor

Influence of coolant crossflow on film cooling effectiveness of one-inlet and double-outlet injection holes

Effects of unsteady wake on heat transfer performance of compound angle blade:numerical simulation

Effects of attack angle and endwall slippage on flow and heat transfer of blade squealer tip

Related Author

LI Guangchao

PENG Ningjian

ZHANG Wei

KOU Zhihai

MAO Xiaodong

ZHANG Guochen

SHEN Yazhou

FU Zhongguang

Related Institution

Liaoning Key Lab of Advanced Measurement and Test Technique for Aviation Propulsion System, Faculty of Aerospace Engineering, Shenyang Aerospace University

Key Laboratory of Condition Monitoring and Control for Power Plant Equipment, Ministry of Education, North China Electric Power University

Aeroengine and Energy Engineering College,Shenyang Aerospace University

School of Energy and Power Engineering, Northeast Dianli University

Harbin Turbine Company Limited

AI问答

⁰