Optimization design of SCR flue gas denitration equipment for a 600MW unit

DONG Chen; QIAO Haiyong; NIU Guoping; ZHANG Bo; WANG Xiaobing

English

您当前的位置：

首页 >

文章列表页 >

Optimization design of SCR flue gas denitration equipment for a 600MW unit

Thermal Power Generation Vol. 43, Issue 12, Pages: 99-104(2014)

更新时间：2025-09-28

- Optimization design of SCR flue gas denitration equipment for a 600MW unit
- 作者机构：
  
  1. 西安热工研究院有限公司
  2. 华能沁北发电有限责任公司
- 作者简介：
- 基金信息：
- DOI：
  CLC： X773
- Published：2014
- 稿件说明：
移动端阅览
DONG Chen, QIAO Haiyong, NIU Guoping, et al. Optimization design of SCR flue gas denitration equipment for a 600MW unit[J]. Thermal Power Generation, 2014, 43(12): 99-104.
DOI：

DONG Chen, QIAO Haiyong, NIU Guoping, et al. Optimization design of SCR flue gas denitration equipment for a 600MW unit[J]. Thermal Power Generation, 2014, 43(12): 99-104. DOI：

摘要

采用数值模拟和模型试验的方法对某600 MW机组选择性催化还原(SCR)烟气脱硝装置的流场进行了优化设计。在挡板门上部加装了导流板

使满负荷和低负荷时挡板门上部的烟气流速均提高到8m/s以上

从而解决了此处大量积灰的问题

且进入第1层催化剂的烟气速度分布、NH3浓度分布、烟气流线与垂直方向夹角和系统阻力均满足技术要求。利用物理模型对第1层催化剂入口的速度场和替代气体浓度场进行了测量

使用烟花示踪的方式观察了系统的流线

并在低负荷下进行了积灰试验

其结果与数值模拟结论一致。

Abstract

Through numerical simulation and model test

the flow field of the SCR flue gas denitration equipment in a 600 MW unit was investigated.Guide plates were added upon the damper to increase the flue gas velocity to higher than 8m/s

which solves the problem of large amount of ash deposition on the damper.Moreover

all the velocity distribution and NH3 mole fraction distribution of the flue gas entering the first catalyst layer

the angle between the flue gas steam and the vertical direction

and the system resistant satisfied the technical requirements.The physical model was applied to measure the velocity field and the alternative gas concentration field at entrance of the first layer of catalyst.By firework tracer

the system streamlines were observed.Ash deposition test was also carried out at low load conditions

of which the results verified the conclusions of the numerical simulation.

关键词

Keywords

references

Views

425

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Numerical modeling and optimal design of flow field for a wet electrostatic precipitator system

Numerical simulation of inner abrasion in a selective catalytic reduction deNOx device

Layout and optimization of a new-type connecting flue with side-inlet and side-outlet for SCR denitrification systems

Resistance characteristics of 90° shrunk bend pipe connector of flue gas duct for a 1 000 MW unit

Related Author

MA Xiuyuan

SHEN Zhiyong

LI Zhiqiang

MA Xiuyuan

SHEN Zhiyong

LI Zhiqiang

ZHONG Yafei

WEI Hongqi

Related Institution

State Power Environmental Protection Research Institute

School of Energy and Environment, Southeast University

Xi’an Thermal Power Research Institute Co., Ltd.

Xi’an Thermal Environmental Engineering Co., Ltd.

School of Power and Mechanical Engineering, Wuhan University

AI问答

⁰