Finite element analysis based thermal characteristic research on direct flow burner in utility boilers

GAO Junru; ZHANG Zheng

English

您当前的位置：

首页 >

文章列表页 >

Finite element analysis based thermal characteristic research on direct flow burner in utility boilers

Thermal Power Generation Vol. 42, Issue 10, Pages: 54-56(2013)

更新时间：2025-09-28

- Finite element analysis based thermal characteristic research on direct flow burner in utility boilers
- 作者机构：
  
  河北工程大学水电学院
- 作者简介：
- 基金信息：
- DOI：
  CLC： TK223.23
- Published：2013
- 稿件说明：
移动端阅览
GAO Junru, ZHANG Zheng. Finite element analysis based thermal characteristic research on direct flow burner in utility boilers[J]. Thermal Power Generation, 2013, 42(10): 54-56.
DOI：

GAO Junru, ZHANG Zheng. Finite element analysis based thermal characteristic research on direct flow burner in utility boilers[J]. Thermal Power Generation, 2013, 42(10): 54-56. DOI：

摘要

以直流煤粉锅炉燃烧器为研究对象

一次风喷口为单元

利用ANSYS有限元分析软件

依据直流煤粉燃烧器的实际工况确定热分析边界条件

建立了燃烧器一次风喷口温度有限元热分析模型。通过分析一次风喷口的温度水平和温度变化梯度

得到在燃烧器正常运行工况下一次风喷口在不同方向上的温度分布

以及在燃烧器正常运行、停运及无周界风3种工况下一次风喷口正对炉膛侧横截面上拐角点温度的变化趋势。结果表明

直流煤粉燃烧器的最高温度集中分布于喷口方形出口的4角附近

这与燃烧器容易发生烧坏、结焦、热变形的部位相符。

Abstract

Taking a direct flow burner as the research object

the primary air nozzle as the unit

the ANSYS software was applied to establish a finite element thermal analysis model for temperature at primary air nozzle of the burner with the boundary condition determined according to the burner's actual working condition.Through investigation on the temperature level and temperature variation gradient at the primary air nozzle

the temperature distribution in different directions of the primary air nozzle under normal working condition was obtained.Moreover

the variation tendencies of temperature at corner point on cross section of the furnace where directly against the primary air nozzle(under three conditions:normal operation

stop state and without surrounding air condition)were also obtained.The results showed that

the highest temperature of the direct flow burner concentrated in four corners of the square exit of the primary air nozzle

which agreed with the locations where the burnout

slagging and thermal deformation easily occurred.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Online measurement of temperature field in furnace based on optical tomography

Numerical simulation of reverse-tangent and swirling-eliminationfor SOFA of boiler co-firing biomass gas with coal

Influence of closing-to-wall air on flow characteristics of a boiler’s secondary-air-box: numerical simulation

Numerical simulation of combustion process in a tangentially pulverized-coal-fired boiler under variable load operation

Fly ash carbon content prediction and combustion optimization adjustment based on ISSA-RF-SSA

Related Author

杨文虎

牛世斌

李翔

荣誉佳

王浩帆

方顺利

晋中华

马帅

Related Institution

College of Electric Power, North China University of Water Resources and Electric Power

School of Electric Power, North China University of Water Resources and Electric Power

State Key Laboratory of Clean Energy Utilization, Zhejiang University

Zhejiang Energy Group R&D

Xinxiang Aviation Industry (Group) Co.,Ltd.

AI问答

⁰