High exhaust temperature of an HG-1900 / 25.4-HM2boiler : cause analysis and countermeasures

SONG Dayong1; DI Wanfeng2; ZHANG Jiawei 1; WU Ju1; ZOU Tianshu1 1.Electric Power Research Institute of Liaoning Electric Power Co.

English

您当前的位置：

首页 >

文章列表页 >

High exhaust temperature of an HG-1900 / 25.4-HM2boiler : cause analysis and countermeasures

Thermal Power Generation Vol. 42, Issue 7, Pages: 109-114(2013)

更新时间：2025-09-28

- High exhaust temperature of an HG-1900 / 25.4-HM2boiler : cause analysis and countermeasures
- 作者机构：
  
  1. 辽宁省电力有限公司电力科学研究院
  2. 华润电力(贺州)有限公司
- 作者简介：
- 基金信息：
- DOI：
  CLC： TK227
- Published：2013
- 稿件说明：
移动端阅览
SONG Dayong1, DI Wanfeng2, ZHANG Jiawei 1, et al. High exhaust temperature of an HG-1900 / 25.4-HM2boiler : cause analysis and countermeasures[J]. Thermal Power Generation, 2013, 42(7): 109-114.
DOI：

SONG Dayong1, DI Wanfeng2, ZHANG Jiawei 1, et al. High exhaust temperature of an HG-1900 / 25.4-HM2boiler : cause analysis and countermeasures[J]. Thermal Power Generation, 2013, 42(7): 109-114. DOI：

摘要

从设计和实际运行两方面对HG-1900/25.4-HM2型锅炉排烟温度高的原因进行了分析。结果表明:(1)受烟气流量和烟气比热容增加等因素的影响

褐煤锅炉的排烟温度设计值比一般烟煤锅炉高约20℃;(2)再热器挡板开度过小使尾部受热面整体换热效率下降、尾部受热面积灰严重等造成空气预热器入口烟温高于设计值

空气预热器出口空气流量与理论空气流量之比(β″)下降。空气预热器入口风温高于设计值等是造成排烟温度高于设计值的主要原因。对此

通过采用提高磨煤机出口风温设定值、优化吹灰方式、增加再热器烟气挡板开度等措施

使排烟温度下降15～20℃

排烟温度恢复到设计值范围。

Abstract

The cause of high exhaust gas temperature of an HG-1900/25.4-HM2boiler was analyzed from design and operation aspects.The results showed that:(1)because of the increase of flue gas volume and specific heat capacity and other factors

the design value of exhaust temperature of boilers firing lignite coal was about 20℃higher than that firing bituminous coal;(2)a decrease in total heat transfer efficiency of tail heating surface caused by over small opening degree of the reheater damper

the gas temperature at air preheater inlet was higher than the design value which caused by serious fouling on the tail heating surface

drop of the air volume and theoretical air volume ratio(β″)at the air preheater outlet

and the gas temperature at air preheater inlet was higher than the design value were the main reasons for high exhaust temperature.Thus

measures such as increasing the air temperature set value at coal mill outlet

optimizing the soot blowing and enlarging opening degree of the reheater gas damper were adopted.After the improvement

the exhaust temperature decreased by 15℃to 20℃

returning to normal.

关键词

Keywords

references

Views

156

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

COMBUSTION ADJUSTMENT TEST FOR SUPERCRITICAL BOILER OF 600MW UNIT

Practice of deep peak load regulation for a 600 MW supercritical concurrent boiler

Anti-blocking optimization of GGH in wet flue gas desulfurization system of a 300 MW unit boiler

Ash accumulation degree model for heating surface based on flue heat distribution

Flame stability upgrading scheme of supercritical boilers for ultra low load peak regulation operation

Related Author

WNAG Da-fengZhejiang Provincial Electric Power Testing & Research Institute

LU Ying

NIE Xin

CHENG Ruishen

HAN Lei

LIU Honggang

ZHOU Ke

ZHANG Guangcai

Related Institution

Zhejiang Electric Power Test and Research Institute

Huaizhe Coal and Electricity Co., Ltd. Fengtai Power Generation Branch

Xi'an Thermal Power Research Institute Co., Ltd

State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology

Guangdong Electric Power Development Co., Ltd. Shajiao A Power Plant

AI问答

⁰