Fault diagnosis method of turbine flow passage based on on-site thermal parameters and its application

XUE Zhaonan; GAO Dengpan; ZHANG Yonghai; ZHI Desheng; ZENG Lifei; SHI Hui; ZHANG Xueyan

doi:10.19666/j.rlfd.202006171

English

您当前的位置：

首页 >

文章列表页 >

Fault diagnosis method of turbine flow passage based on on-site thermal parameters and its application

Thermal Power Generation Vol. 50, Issue 4, Pages: 143-148(2021)

更新时间：2025-09-28

- Fault diagnosis method of turbine flow passage based on on-site thermal parameters and its application
- 作者机构：
  
  1. 西安热工研究院有限公司
  2. 深圳妈湾电力有限公司
- 作者简介：
- 基金信息：
- DOI：10.19666/j.rlfd.202006171
  CLC： TM621
- Published：2021
- 稿件说明：
移动端阅览
XUE Zhaonan, GAO Dengpan, ZHANG Yonghai, et al. Fault diagnosis method of turbine flow passage based on on-site thermal parameters and its application[J]. Thermal Power Generation, 2021, 50(4): 143-148.
DOI：

XUE Zhaonan, GAO Dengpan, ZHANG Yonghai, et al. Fault diagnosis method of turbine flow passage based on on-site thermal parameters and its application[J]. Thermal Power Generation, 2021, 50(4): 143-148. DOI： 10.19666/j.rlfd.202006171.

摘要

汽轮机故障诊断关系到整个电厂的安全经济运行。热力参数故障诊断可实现早发现

并能快速定位故障位置。本文提出了基于现场热力参数的级组效率和特征通流面积的诊断方法

并结合现场实际数据对该方法进行验证;采用基于现场热力参数的特征通流面积和级组效率的诊断方法

实现对机组通流状态的在线监测与诊断分析。通过对某电厂300 MW机组故障诊断研究发现:级组效率和特征通流面积在主蒸汽到调节级段、中压缸进汽到三段抽汽级段发生了明显变化;基于调节阀门开度流量特性

分析发现主蒸汽到调节级的效率和特征通流面积变化是由高压调节阀开度变化引起的;中压缸进汽到三段抽汽级段的特征通流面积减小约7.2%级组效率下降5.7%

判定故障发生在该级组段

诊断结果准确可靠

与现场实际完全吻合。

Abstract

Fault diagnosis of steam turbine is related to the safe and economical operation of the whole power plant. The fault diagnosis of thermal parameters can realize early detection and can quickly locate the fault position. In this paper

the diagnosis method of characteristic flow area and stage group efficiency based on on-site thermodynamic parameters is adopted to realize on-line monitoring and diagnosis analysis of unit flow state. Through fault diagnosis for a 300 MW unit

it is found that the efficiency and characteristic flow area of the stage group have changed obviously in the stage from main steam to the governing stage and stage from the inlet of intermediate pressure cylinder to the third extraction point. Based on the characteristics of governing valves

it is found that the change of efficiency and characteristic flow area from the main steam to the governing stage is caused by opening change of the high-pressure governing valves. The characteristic flow area reduces by 7.2%

and the efficiency decreases by 5.7%. Therefore

the fault is judged to have occurred at stage from the inlet of intermediate pressure cylinder to the third extraction point. The diagnosis results are accurate and completely consistent with the actual situation.

关键词

Keywords

references

Views

404

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Fault diagnosis method of turbine flow passage based on improved KNN algorithm and its application

Spectrum and shaft center orbit based fault feature extraction and diagnosis for steam turbines

Progress of quantitative evaluation of wetness losses in steam turbine

Identification method for flow characteristics of steam turbine based on characteristic flow area

Research on fault diagnosis benchmark of large scale unit based on fuzzy analysis and information entropy

Related Author

LYU Cheng

CHEN Shiyi

HUA Xinguo

XIANG Wenguo

GAO Junru

SUN Yajun

BAN Muyuan

HAN Zhonghe

Related Institution

Key Laboratory of Energy Heat Conversion and Process Measurement and Control, Ministry of Education, Southeast University

College of Hydroelectric Engineering, Hebei University of Engineering

Key Laboratory of Power Station Equipment Status Monitoring and Control, Ministry of Education, North China Electric Power University

State Grid Henan Electric Power Company Electric Power Science Research Institute

School of Energy and Power Engineering, Huazhong University of Science and Technology

AI问答

⁰