Performance analysis and working fluid selection of organic Rankine cycle system with variable temperature heat source based on NSGA-Ⅱ algorithm

MA Xinling; QIU Yuheng; MENG Xiangrui; PAN Jiahao; WANG Shuangquan

doi:10.19666/j.rlfd.202208168

English

您当前的位置：

首页 >

文章列表页 >

Performance analysis and working fluid selection of organic Rankine cycle system with variable temperature heat source based on NSGA-Ⅱ algorithm

Thermal Power Generation Vol. 52, Issue 4, Pages: 82-89(2023)

更新时间：2025-09-28

- Performance analysis and working fluid selection of organic Rankine cycle system with variable temperature heat source based on NSGA-Ⅱ algorithm
- 作者机构：
  
  郑州大学机械与动力工程学院
- 作者简介：
- 基金信息：
- DOI：10.19666/j.rlfd.202208168
  CLC： TK115
- Published：2023
- 稿件说明：
移动端阅览
MA Xinling, QIU Yuheng, MENG Xiangrui, et al. Performance analysis and working fluid selection of organic Rankine cycle system with variable temperature heat source based on NSGA-Ⅱ algorithm[J]. Thermal Power Generation, 2023, 52(4): 82-89.
DOI：

MA Xinling, QIU Yuheng, MENG Xiangrui, et al. Performance analysis and working fluid selection of organic Rankine cycle system with variable temperature heat source based on NSGA-Ⅱ algorithm[J]. Thermal Power Generation, 2023, 52(4): 82-89. DOI： 10.19666/j.rlfd.202208168.

摘要

针对120～150℃烟气余热，建立亚临界有机朗肯循环系统的数学模型。首先以R245fa为例，在不同热源温度下对系统进行了热力性能和经济性能分析；其次选取6种纯工质，基于NSGA-Ⅱ算法对系统进行了多目标优化研究；最后通过TOPSIS法和灰色关联分析对不同热源温度下的系统进行了工质选择和性能分析。结果表明：在研究温度范围内，过热度和蒸发器夹点温差的升高均不利于提升系统性能；不同热源温度下的最佳工质不同，热源温度为120℃时，R601的热力性能最优，R245fa的经济性最优，R1233zd的综合性能最优；热源温度的升高有利于提升系统的经济性能，各工质的最佳蒸发温度随着热源温度的升高而升高。灰色关联分析表明，6种工质的综合性能均随着热源温度升高有所提升。

Abstract

A mathematical model of subcritical organic Rankine cycle(ORC) system is established for the flue gas waste heat of 120～150 ℃. Firstly

the thermal performance and economic performance of the system are analyzed at different heat source temperatures by taking R245fa as an example. Then

a multi-objective optimization study is conducted for six pure working fluids based on NSGA-Ⅱ algorithm. At last

working fluid selection and performance analysis of the ORC system with various heat source temperatures are carried out by TOPSIS method and gray correlation analysis. The results show that

in the temperature range of this study

the increase of superheat degree and evaporator pinch point temperature difference is not conducive to improve the system performance. The optimal working fluids are varied at different heat source temperatures

when the heat source temperature is 120 ℃

R601has the best thermal performance

R245fa has the best economic performance and R1233zd has the best overall performance. The increase of heat source temperature is beneficial to improve the economic performance of the system. The optimal evaporation temperature of each working fluid increases with the heat source temperature. The gray correlation analysis indicates that the comprehensive performance of all six working fluids improves with the heat source temperature.

关键词

Keywords

references

Views

448

下载量

CSCD

Alert me when the article has been cited

提交

Publicity Resources

Performance evaluation and comparison of novel combined power cycles consisting of partial pre-heating supercritical carbon dioxide power cycle and different absorption power cycles for waste heat recovery

Road adaptability of hybrid trucks integrated with a full-condition efficient waste heat recovery system

STUDY ON MULTI-OBJECTIVE OPTIMIZATION FOR CONTROL SYSTEM OF THE THERMAL PROCESS AND ITS APPLICATION IN BOILER-TURBINE COORDINATED CONTROL

Thermodynamic performance analysis of graded regenerative extraction organic Rankine cycle system

Waste heat recovery from circulating cooling water in power plants

Related Author

HU Hao

GUO Qianxin

YANG Li

YU Xiaobing

XUE Chenxi

LIU Yonglin

XUE Yanping

YANG Qingchuan

Related Institution

Shenhua Shendong Electric Power Co., Ltd. Technical Research Institute

Xi'an Thermal Power Research Institute Co., Ltd

Xi'an Xire Energy saving Technology Co., Ltd

Shenhua Shendong Electric Power Co., Ltd. Dianta Power Plant

School of Mechanical Engineering, Tianjin University

AI问答

⁰