单轴联合循环发电机组燃气轮机与汽轮机功率区分方法研究

胡孟起; 肖俊峰; 吴昌兵; 周刚; 向东; 王科; 赵思勇; 葛晓明; 刘印; 夏林; 连小龙; 王一丰

doi:10.19666/j.rlfd.202112263

English

您当前的位置：

首页 >

文章列表页 >

单轴联合循环发电机组燃气轮机与汽轮机功率区分方法研究

热力发电 2022年51卷第6期页码：132-138

发电技术论坛 | 更新时间：2025-09-28

- 单轴联合循环发电机组燃气轮机与汽轮机功率区分方法研究
- Research on method for distinguishing power output of gas turbine from steam turbine in single-shaft combined cycle power unit
- 作者机构：
  
  1. 西安热工研究院有限公司
  2. 华能重庆两江燃机发电有限责任公司
- 作者简介：
- 基金信息：
- DOI：10.19666/j.rlfd.202112263
  中图分类号： TM611.31
- 纸质出版：2022
- 稿件说明：
移动端阅览
胡孟起, 肖俊峰, 吴昌兵, 等. 单轴联合循环发电机组燃气轮机与汽轮机功率区分方法研究[J]. 热力发电, 2022,51(6):132-138.

HU Mengqi, XIAO Junfeng, WU Changbing, et al. Research on method for distinguishing power output of gas turbine from steam turbine in single-shaft combined cycle power unit[J]. Thermal Power Generation, 2022, 51(6): 132-138.
胡孟起, 肖俊峰, 吴昌兵, 等. 单轴联合循环发电机组燃气轮机与汽轮机功率区分方法研究[J]. 热力发电, 2022,51(6):132-138. DOI： 10.19666/j.rlfd.202112263.

HU Mengqi, XIAO Junfeng, WU Changbing, et al. Research on method for distinguishing power output of gas turbine from steam turbine in single-shaft combined cycle power unit[J]. Thermal Power Generation, 2022, 51(6): 132-138. DOI： 10.19666/j.rlfd.202112263.

摘要

单轴联合循环发电机组中燃气轮机输出功率和汽轮机输出功率的合理区分是联合循环机组运行状态监测与性能分析领域亟需解决的重要问题之一。基于燃气轮机和汽轮机的基本原理，提出一种实施方便、通用性强的单轴联合循环机组燃气轮机与汽轮机功率区分方法。结果表明：采用该方法获得的计算结果与某F级单轴联合循环机组（匹配三压再热凝汽式汽轮机）热平衡设计数据对比，汽轮机功率的最大相对偏差为1.6%，燃气轮机功率的最大相对偏差为–1.42%。这表明本文提出的功率区分方法具有较好的计算精度，可为相关工程应用提供参考和借鉴。

Abstract

Predicting the output powers of gas turbine and steam turbine distinctively in single-shaft combined cycle power plant(CCPP) is one of the most significant problems for operating condition monitoring and performance analysis for the CCPP. Based on the theoretical principles of single-shaft combined cycle units

a mathematical method with practical implement and strong versatility was proposed in this paper to calculate the power output of gas turbine and steam turbine distinctively. The results show that

compared with the heat-balance design data of a single-shaft CCPP with an F-class gas turbine and a triple-pressure steam-reheat condensing steam turbine

the maximum relative deviation between calculation results by the proposed method and design data is 1.6% for steam turbine power output and -1.42% for gas turbine power output

which indicates that the proposed numerical method has good calculation accuracy and can provide reference for engineering applications.

关键词

Keywords

references

浏览量

236

下载量

CSCD

文章被引用时，请邮件提醒。

提交

关联资源

汽轮机转子温度场有限元法简化计算模型

固体自润滑技术在发电厂的应用

双抽可调式汽轮机控制系统整定研究

大型燃气轮机余热锅炉进口烟道速度均匀性研究

180MW燃气-蒸汽联合循环机组汽轮机并网带初负荷故障分析